Auctions & Liquidations

Private Treaty Sale | Trion Battery | Battery Cell Productionlines

Listing 1.1:Automatic Battery Cell Assembly Line by GROHMANN Engineering

Buyers Premium: 18%

Tax Rate on Hammer Price: 19%

Tax Rate on Buyers Premium: 19%

Tax Rate on Charges: 19%

Listed Until Dec 10, 2026, 9:00 AM UTC
Register for Auction

Description

Type Fully Automatic Battery Cell Assembly Line (EFA2)
Make Grohmann Engineering
Model EFA – Cell Assembly Line
Year of Manufacture 2012
Condition Used
Quantity 1

 

Lot consists of:

(1) Fully Automatic Battery Cell Assembly Line "EFA2" (Grohmann Engineering), consisting of (1) Module CB01 Electrode and Separator Unwinding with Inline Drying, (1) Module CB02 Laser Cutting and Cleaning Station, (1) Module CB03 Pick & Place Transfer, (1) Module CB04 Stacking and Indexing Station, (1) Module CB05 Stack Fixation and Tab Welding Station, (1) Module CB06 Housing Deep Drawing and Packing/Sealing Station, (1) Module CB07 Electrolyte Filling and Wetting Station, (1) Module CB08 Vacuum Final Sealing Station, (1) Module CB09 Final Cutting, Weighing, Marking and Discharge Station, (2) 6-Axis Industrial Robots (Stäubli TX90), Row of Control Cabinets, Operator Terminals and Line Peripherals

 

Item Description:

Fully automatic assembly line for prismatic lithium-ion pouch cells, built by Grohmann Engineering as one of three identical lines (designated EFA) at the Kamenz cell plant. The line takes in anode, cathode and ceramic separator from reels and delivers the finished, filled and sealed cell ready for formation — drying, laser cutting, single sheet stacking, fixation, tab welding, housing forming, sealing, electrolyte filling and final cutting are all integrated into one continuous process inside a dry room.

The line is of very compact design at approximately 30 m length per line and was engineered for short cycle times at automotive quality level. Its distinctive features are the inline drying concept without vacuum, full laser cutting of electrodes and separator instead of mechanical tooling, single sheet stacking to a tolerance of 0.3 mm, torsional ultrasonic tab welding without pre-welding or retaining plates, and hot-cold sealing of the pouch housing.

The line is built as a row of enclosed, glazed station cabins in aluminium profile. Each station has its own operator terminal running the Grohmann HOC-500 user interface, with emergency stop, signal column and compressed air maintenance unit. A continuous row of control cabinets with built-in screens and pull-out keyboards runs along the line. Workpiece carriers and vacuum belt conveyors link the modules; two six-axis robots serve the fixation and handling stations.

The line was in production until the plant was shut down and can be inspected in its installed condition. Technical documentation and a comprehensive spare parts inventory for the EFA lines are available.

 

Line Modules:

CB01 – Electrode and Separator Unwinding with Inline Drying (sub-stations 1010 – 1080)

  • unwinding stations for anode, cathode and ceramic separator reels in glazed cabins
  • reel drives with clamping spindles and pneumatic expanding shafts (SWY 150/3)
  • BST International web edge guiding with ekr 500 plus controller and infrared edge sensors
  • Eltex static discharge units
  • inline drying section with Elstein high-temperature radiant heaters, two types of radiant heating, thermocouple monitored
  • inline drying of electrodes and ceramic separator plus inline annealing of electrodes
  • drying without vacuum, drying time < 10 min, dew point −55 °C

CB02 – Laser Cutting and Cleaning (OP200 / OP300, sub-stations 2010 – 2040, branches CB02.1 / CB02.2)

  • station plates CB02.2 OP200 / OP300 ANODE LASERSCHNEIDEN and OP300+030 ANODE REINIGEN
  • dual laser unit on C-frame for anode and cathode, separate separator laser
  • IPG ytterbium pulsed fibre laser sources (YLP-HP series), 2 × 200 W for the electrodes
  • Raylase Axialscan AS50 scan heads with SP-ICE control cards and MOTF mark-on-the-fly boards
  • beam expanders, bending mirrors and protective glasses (Laser Components, Raylase)
  • cutting speed approx. 1 m/s, no tool wear, free choice of cutting geometry
  • downstream cleaning station for the cut sheets
  • SICK safety light curtains at the laser openings, laser safety windows, extraction at the cutting point

CB03 – Pick & Place Transfer (sub-stations 3010 – 3080)

  • pick & place modules with vacuum gripper heads for the cut sheets
  • pick & place camera system for sheet position control
  • vacuum belt conveyors for anode, separator and cathode

CB04 – Stacking and Indexing (OP400)

  • station plate CB04 OP400 stapeln Anode/Separator
  • single sheet stacking of electrodes and separator in one step, no bending of the active material
  • stacking tolerance 0.3 mm
  • eight stacking positions with vacuum belts, gantries and magazine racks
  • stack and indexing unit, gripper system for stack fixation
  • workpiece carrier lift and buffer section

CB05 – Stack Fixation and Tab Welding (sub-stations 5010 – 5090)

  • taping unit applying PP tape, seven fixation points per stack
  • rotary table with Bosch Rexroth linear axes and SMC pressure regulator panel
  • vision system controller for fixation inspection
  • tab handling system and transport indexing unit
  • torsional ultrasonic welding (Telsonic) without pre-welding or additional retaining plates
  • four welding spots per tab, overall retention force over 1,000 N
  • 20 kHz torsional sonotrodes and coated anvil plates, separate geometries for copper and aluminium
  • served by a 6-axis industrial robot

CB06 – Housing Deep Drawing and Packing/Sealing (sub-stations 6010 – 6130)

  • inline deep drawing of the pouch housing half shells with load-optimised geometry
  • deep drawing tool with die for the 50 Ah cell format
  • automatic splicer for the packaging film
  • punching of index holes with local extraction
  • clamping unit on rotary table, highly precise alignment of the half shells
  • hot-cold sealing with separate hot-seal and cold-seal bars for head and side seams
  • Kollmorgen servo drives with Servostar 700 amplifiers

CB07 – Electrolyte Filling and Wetting (OP1100, hook-on module)

  • station plate CB07 OP1100 ELEKTROLYT BEFÜLLEN, HOOK-ON-MODUL
  • Hibar high-precision dosing system for electrolyte filling
  • gravimetric filling level measurement, specified tolerance ±2 g, achieved in production ±0.5 g
  • vacuum chambers with VAT vacuum valves and sealing jaws
  • multi-cycle wetting supported by the ceramic separator, very short cycle times

CB08 – Vacuum Final Sealing

  • final sealing of the filled cell under vacuum
  • hot and cold sealing bars for maximum longevity and seam cohesion

CB09 – Final Cutting, Weighing, Marking and Discharge (OP1200)

  • edge trimming to the final cell dimensions within narrow tolerance
  • end sealing bars right and left with energy chains
  • turntable OP1200
  • integrated weighing station
  • integrated marking printer for cell identification
  • automatic reject discharge station for out-of-tolerance cells

Line-wide Equipment

  • (2) 6-Axis Industrial Robots (Stäubli TX90) at the fixation and handling stations
  • Grohmann HOC-500 operator interface at every station in a glazed operator console
  • enclosed aluminium profile cabins with safety interlocks, emergency stops and signal columns
  • compressed air maintenance units and extraction connections per station
  • row of control cabinets with built-in screens and pull-out keyboards
  • Siemens and Beckhoff control hardware, SICK, Pilz and Schmersal safety technology
  • rack-mounted electrical test instruments at the handling station

 

Line Performance Data:

  • footprint approx. 30 m line length, very compact design
  • cell formats produced: 52 Ah (HEA-50, 330 × 186 × 12.7 mm, 1,290 g) and 40 Ah (HEA-40, 245 × 203 × 11.3 mm, 1,040 g)
  • process chain: drying – laser cutting – stacking – fixation – tab welding – packing/sealing – filling/wetting – final sealing/cutting
  • operated in a dry room environment
  • formation without degassing, enabled by the upstream process design

 

Please note: The line is sold as one lot in its installed condition, as it stands. Designations and technical data are taken from the operator's documentation and from the markings and station plates on the machine, and are stated to the best of our knowledge. No warranty is given as to completeness, function or fitness for a particular purpose. Dismantling and removal are the responsibility of the buyer. Inspection before bidding is strongly recommended.


click here to view the 3D-Tour

Further Information

Delivery Conditions EXW (Incoterms 2020)
Payment Term Immediately upon Invoice receipt

 

IMPORTANT – SALE SUBJECT TO SELLER APPROVAL: This lot is offered subject to the express approval of the seller, Trion Battery GmbH. Submission of the highest bid does not create any entitlement to purchase or to be awarded the lot. The lot will only be sold to the highest bidder if the seller approves the sale. The highest bidder will be informed of the seller's acceptance or rejection within 3 days after the close of the auction.



DO YOU HAVE ANY QUESTIONS? PLEASE CONTACT ME!

Sebastian Geissler
Senior Project Manager
Tel: +49 176 10 43 16 23
E: sebastiang@maynards.com

 

This website's original content is provided in English. Translations into other languages are AI-generated and offered solely for user convenience; they may contain errors or inaccuracies. In case of any inconsistency, the English version prevails. No liability is assumed for misunderstandings or damages arising from translated content. Users should refer to the English version for authoritative information.

Auction Software by Bidlogix